Vidalı Hava Kompresörlerindeki Temel Bileşenlerin Doğru Bakımı

Routine and proper maintenance of key components in screw air compressors is essential for prolonging equipment lifespan and ensuring reliable operation. This guide outlines best practices for maintaining major parts such as the air filter, oil filter, oil separator, lubricant, cooler, minimum pressure valve, and oil return check valve.

The air intake filter removes dust and debris from the ambient air before it enters the compressor. Since the rotor clearance inside the screw compressor only tolerates particles smaller than 15 microns, any filter blockage or damage can allow large particles to enter the system, leading to:

• Reduced oil filter and oil separator lifespan
• Increased bearing wear
• Enlarged rotor clearance
• Lower compression efficiency
• Risk of rotor seizure

Recommended maintenance:

• Weekly cleaning: Remove the filter element and blow compressed air (0.2–0.4 MPa) from the inside out to remove surface dust. Clean the filter housing with a lint-free cloth.
• Replacement frequency:
  • Normal environments: every 1000–1500 hours
  • Harsh environments (mines, ceramics, textiles): every 500 hours

🔧 İpucu: When cleaning or replacing, ensure no foreign objects fall into the air intake valve. Also inspect the intake hose for damage or leaks.

The oil filter traps impurities in the lubricant, protecting the compressor rotor and bearings.

Initial replacement:

• Replace the oil filter after the first 500 hours of operation (new unit break-in period).

Regular replacement:

• Every 1500–2000 hours, preferably along with an oil change. In dusty or high-temperature environments, replace more frequently.

⚠️ Warning: Do not exceed the usage limit. A clogged filter can trigger the bypass valve, allowing contaminants to enter the rotor chamber and cause severe damage.

The oil separator removes lubricant from compressed air. Its normal lifespan is around 3000 hours, but this varies based on oil quality and air cleanliness.

When to replace:

• After 3000 hours, or
• When pressure differential exceeds 0.12 MPa

Replacement steps:

1. Disconnect control lines from the separator tank.
2. Remove the oil return pipe and the separator tank lid.
3. Take out the used oil separator element.
4. Install a new element with asbestos gaskets properly aligned and stapled to avoid leaks.
5. Reassemble all parts and check for air/oil leakage.

Using the correct screw compressor oil significantly affects machine performance. Always use Baldor’s original synthetic screw compressor oil, which features:

• Excellent oxidation stability
• Quick separation
• Low foaming
• High viscosity
• Anti-corrosion protection

Oil replacement intervals:

• First change: after 500 hours
• Subsequent changes: As specified in the user manual, or more frequently in harsh environments

Replacement procedure:

1. Run the compressor for 5 minutes to warm up the oil.
2. After stopping and depressurizing, drain the oil from the tank and pipelines.
3. Replace the oil filter and refill with fresh oil to the indicated level.
4. Check for leaks and confirm oil level stability.

⚠️ Important: Never mix different brands of oil. Avoid using expired oil, which may lead to high-temperature shutdowns or even oil combustion.

The heat exchanger plays a crucial role in controlling operating temperature. Due to the finned structure, dust accumulation is common.

Cleaning frequency:

• Each shift: Use dry compressed air (>0.4 MPa) to blow dust from top to bottom
• For diesel-driven compressors, blow from the outside inward

For oily environments: Use a carbon deposit cleaner to remove oil residues thoroughly.

This small but critical valve helps:

• Build internal system pressure
• Enable proper lubrication oil circulation
• Prevent backflow during unloading

Components: valve body, valve core, adjustment screw, spring, sealing parts

Cleaning:
Disassemble and clean using the same method as the unloading valve. Pay special attention to the direction of U-shaped seals when reassembling.

This valve ensures that separated oil returns to the compressor for lubrication.

Structure: valve body, steel ball, spring, and seat

Function:

• Allows separated oil to flow back to the rotor chamber
• Prevents oil from entering the air outlet
• Minimizes oil consumption

Maintenance tip: Clean and inspect regularly to ensure smooth oil circulation and avoid performance loss or overheating.

Regular maintenance of your screw air compressor’s filters, oil, valves, and cooler is essential for preventing breakdowns, optimizing energy efficiency, and ensuring long service life. For best results, always use Baldor-certified parts and lubricants.

🔧 Need professional compressor maintenance or spare parts?
Visit Baldor Services & Support »